![]() ![]() Enable EuCon Support - When checked, MIO Console will automatically connect to EuCon services if you have the EuCon software and hardware installed.This does not apply to EuCon Control surfaces as EuCon manages application switching. Uncheck this if you will use the same control surface units in another host program too. Use Control Surface while in background - When checked, MIO Console will continue to use the Mackie Control Protocol Control Surface units, even if it is not the active application on your computer. ![]() MIO Console will place this fader pack to the left of Fader Pack 2 in terms of fader layout Fader Pack 3 - Select the MIDI ports for the Mackie Control Protocol first fader pack used in the system.MIO Console will place this fader pack to the left of Fader Pack 1 in terms of fader layout Fader Pack 2 - Select the MIDI ports for the Mackie Control Protocol first fader pack used in the system.MIO Console will place this fader pack to the left of the Primary Controller in terms of fader layout Fader Pack 1 - Select the MIDI ports for the Mackie Control Protocol first fader pack used in the system.MIO Console will treat this as the right-most controller in terms of fader layout Primary Controller - Select the MIDI ports for the primary (generally the master section) Mackie Control Protocol control surface unit.Use the controller popups to select the MIDI I/O for your control surface. Enable Control Surface Support - When checked, MIO Console will listen to Mackie Control protocol messages on the specified MIDI Ports.The relevant preferences for Control Surface support are: When you select the Preferences command, the Preferences sheet is shown on the MIO Console window: These preferences are accessed via the MIO Console > Preferences… command (or via the -, key sequence). This is done from the MIO Console Preferences panel. The first step in using the Control Surface support is enabling and configuring your Control Surfaces. More interesting, however, is that the two different control surface systems can be used to control different parts of MIO Console at the same time, allowing you to control different parts of a mix or even two different mix busses simultaneously with multiple control surface units. If both controllers are controlling the same elements of MIO Console, MIO Console will keep both protocols synchronized. Both protocols are supported simultaneously, so you can use both types of controllers at the same time. MIO Console supports two different Control Surface communication protocols: Euphonix’s EuCon and Mackie Design’s Mackie Control Protocol. This enables the use of host-based reverbs and delays with greatly simplified routing.MIO Console v.5.1 adds extensive support for external tactile control surface units. This new feature also allows inserting processors that are hosted on the computer directly within the signal flow of the MIO low-latency hardware mixer. I/O inserts streamline the use of external analog and digital processors within the MIO mixer. For live sound and monitoring applications this allows the user to disconnect and reconnect the computer or quit and launch MIO Console without being concerned about introducing dropouts to ongoing primary and backup recordings or to the monitoring paths for talent. With ConsoleSync, new users will experience a dramatically reduced learning curve for accessing the power of MIO Console.Įxperienced users will value the ability to have MIO Console re-connect to the hardware with exact recall of the current hardware state and no disruption of audio. ConsoleSync allows MIO Console to read the complete state of any attached hardware seamlessly, automatically and without any disruption of running audio.ĬonsoleSync auto loads the mixer configuration, complex signal processing chains, Monitor Controller settings, analog I/O configuration and even window layout from the hardware. In addition to these new features, v.5.6 continues to improve stability and compatibility with current and future versions of Mac OS X, from 10.6.8 to 10.8.x and beyond.ĬonsoleSync is a unique enhancement to the Mobile I/O family that benefits both new and experienced users. AAX ConsoleConnect plug-in for compatibility with Pro Tools 11.ConsoleSync hardware/software synchronization technology.I/O inserts for accessing external hardware from within the MIO Mixer.V.5.6 includes the following new features: Metric Halo is pleased to announce the immediate availability of MIO Console v.5.6, a free software upgrade for all users of the Mobile I/O family of audio interfaces, including the award-winning 2882, ULN-2, LIO-8 and ULN-8. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |